PEEK Unsplash Free LaboratoryThe optimal balance of chemical, mechanical and thermal properties

PEEK fasteners (chemically known as Polyetheretherketone) offer a unique combination of properties for some of the most extreme applications. PEEK is classified as semicrystalline thermoplastic and high purity polymer, offering excellent mechanical strength and chemical resistance at high temperatures. PEEK fasteners offer a high strength alternative to PTFE fluoropolymers.

Key Benefits

  • Excellent resistance to thermal degradation (chemical decomposition caused by heat).
  • Chemically resistance to many oils, alcohols, solvents, and organics as well as harsh acids and bases in low concentrations and temperatures.
  • Hydrolysis resistance provides PEEK ability to retain all physical properties when continuously exposed to water or steam at high temperatures and pressures, as well as offer very low moisture absorption.
  • Outstanding creep resistance allows PEEK fasteners to sustain large stresses over long service life.
  • Ability to withstand frequent sterilization processes.
  • V-0 flammability rating with low smoke and toxic gas emission when exposed to flame.
  • Good wear and abrasion resistance.
  • Electrical properties are maintained over a wide frequency and temperature range.
  • Radiation resistance allows PEEK to be used in or be repeatedly sterilized by, high doses of ionizing radiation.

Options for High Strength
Depending on the application, PEEK screws can be reinforced with glass or carbon fibers for improved strength and stiffness properties. Reinforced PEEK fasteners offer greater mechanical robustness especially in applications beyond 350°F (175°C).

PEEK 100% / Unfilled
PEEK, with no fillers is unreinforced and 100% polymer. Even without glass or carbon fiber reinforcement, this one of the strongest polymers we offer and well suited for a variety of applications including FDA food contact and other applications requireing high purity.

PEEK Glass Fiber Reinforced
Offers the same chemical resistance and natural PEEK but nearly doubles in tensile strength.

PEEK Carbon Fiber Reinforced
Provides approximately 2.5 times the strength of pure PEEK.

PEEK Extreme
This is our proprietary receipe for the highest strength PEEK utilizing carbon fiber reinforcement. This version of PEEK over 3 times stronger than standard unreinforced PEEK.

Applications

  • Viewed by the medical community as an advanced biomaterial, PEEK fasteners are used in medical implants and are compatible with a high-resolution magnetic resonance imaging (MRI).
  • PEEK fasteners are one of the few plastics compatible with ultra-high vacuum (UHV) which is necessary for many analytic techniques and particle accelerators.
  • Chemical processing and pharmaceutical applications depend on PEEK for it’s chemical resistance, high purity and ability to withstand sterilization processes.
  • PEEK fasteners are used in many electronics from cell phones to circuit boards for their lightweight strength and reduced noise, vibration and harshness (NVH).

PEEK Fastener Stock and Availability

Stock
PEEK screws, bolts, nuts and washers are available and ready to ship in many common sizes. You can purchase many of these directly from our online webstore. In addition, we stock other PEEK fasteners. Please contact us for a specific size and part you need.

Custom Availability
PEEK screws and fasteners can be made to order in many different styles and sizes with minimum quantities, typically around 25 pieces. Fasteners can be produced in pure PEEK, glass-filled PEEK, carbon-filled PEEK and PEEK Extreme. We also have the capability to produce unique, per-print custom fasteners. The normal lead time for custom PEEK fasteners about 4 weeks.  Be sure to contact us for specific lead times and expediting needs.
o  Diameter sizes:  Standard #00 – 4” in diameter / Metric M1.2 – M48
o  Threads: UNC, UNF
o  Minimum Volume – Typically 25pcs depending on size and complexity
o  Custom to print
o  All DIN / ISO standards

Expediting Options
When time is critical, we can help. When requesting a quote, please let us know your lead time requirements so that we can do our best to accommodate your needs.


PEEK Fastener Styles

PEEK Screws Button Head Cap ScrewsFlat Head ScrewsHex Head Cap Screws, Pan Head Screws, Set ScrewsSocket Head Cap Screws
o  DIN 603 / ISO 8677
o  DIN 912 / ISO 4762
o  DIN 913 / ISO 4026
o  DIN 914 / ISO 4027
o  DIN 915 / ISO 4028
o  DIN 916 / ISO 4029
o  DIN 921
o  DIN 931 / ISO 4014
o  DIN 933 / ISO 4017
o  DIN 961 / ISO 8676
o  DIN 965 / ISO 7046
o  DIN 966 / ISO 7047
o  DIN 7991 / ISO 10642
o  DIN 7380 / ISO 7380
o  DIN 84 / ISO 1207
o  DIN 85 / ISO 1580
o  DIN 961 / ISO 8676
o  DIN 7984 
o  DIN 963 / ISO 2009
PEEK Bolts Hex Head Bolts
o  DIN 931
o  DIN 933
o  ISO 4014
o  ISO 4017
o  ISO 7370
PEEK Nuts Hex Nuts o  DIN 439 / ISO 4035
o  DIN 934 / ISO 4032
o  DIN 6923 / ISO 4161
PEEK Studs/Rod Studs, Threaded Rod o  DIN 975
o  DIN 976
PEEK Washers Flat Washers o  DIN 125 / ISO 7089 / ISO 7090
o  DIN 126 / ISO 7091
o  DIN 9021 / ISO 7093

 


Mechanical Properties of PEEK

PEEK Tensile Curves  Tensil Temperature Chart 11 2017

Chemical Resistance of PEEK / Victrex(R) Fastener 

PEEK Chemical Resistance


 

PEEK Properties

PEEK Properties


PEEK Screws  

 Button Head    Button Head Cap Screws PEEK button head screws typically feature a socket driver and offer a wide clamping area and low profile. They are best for fastening material that is too thin to counter bore. o ASME B18.3
o ASME 18.3.4M
o DIN 7380 / ISO 7380
 Flat Head 3D    Flat Head Screws PEEK flat head screws are commonly offererd in a 82° countersink angle, but can be custom made to other angles from 60° -120°. Typically PEEK flat heads have a slotted or phillips drive, but can also be custom made with a socket drive. These screws are designed to be flush with the surface. o  ASME B18.3
o  ASME B18.3.6
o  DIN 963 / ISO 2009
o  DIN 965 / ISO 7046
o  DIN 7991 / ISO 10642
Hex Cap Screw    Hex Head Cap Screws PEEK hex head cap screws feature an added washer face to the bolt head a hex head bolt does not have. Hex head cap screws provide tighter dimensional tolerances over hex bolts. PEEK hex head screws are best for applications that need a high clamping force with easy access. Generally available in #2 - 1/2" sizes and metric sizes. o ASME B18.6.3
o DIN 931 / ISO 4014
o DIN 933 / ISO 4017
o DIN 961 / ISO 8676
pan head screw s    Pan Head Screws Featuring either a slotted or phillips drive, PEEK pan head screws have a rounded head and are best for small diameter fastener needs, as well as low torque applications. o ASME B18.6.3
o DIN 7985
o DIN 921
o DIN 85 / ISO 1580
o DIN 84 / ISO 1207
  (cheese head)
o DIN 966 / ISO 7047
  (raised counter sunk)
Set Screw    Set Screws PEEK set screws are custom made with a cup, cone, flat, dog or half-dog point. Set screws have no head and feature a socket or slotted driver at one end. o ASME B18.3
o DIN 913 / ISO 4026
o DIN 914 / ISO 4027
o DIN 915 / ISO 4028
o DIN 916 / ISO 4029
Socket Head Cap Screw Short Image     Socket Head Cap Screws PEEK socket head cap screws provide a safe reliable fastener in situations where there is limited access or little clearance around the screws. They are also economic. o ASMET B18.3
o DIN 912 / ISO 4762
o DIN 7984

PEEK Bolts 

Hex Bolt    Hex Head Bolts Similar to hex head cap screws, PEEK bolts do not have the added washer face. They are an economic solution to high clamping force applications with easy access. o ASME B18.2.1
o DIN 931 / ISO 4014
o DIN 933 / ISO 4017

PEEK Nuts 

 Hex Nut       Hex Nuts Most common sizes of PEEK hex nuts are stocked and ready to ship. Custom sizes can also be made upon request. o ASME B18.16.3
o ASME B18.2.2
o DIN 439 / ISO 4035
o DIN 934 / ISO 4032
o DIN 986

PEEK Studs & Threaded Rod 

Studs    Studs PEEK studs are fully threaded or partially threaded rodsare less than 12" in length. They can be made to any custom length. o ASME B18.31.2
o DIN 976
Threaded Rod 2    Threaded Rod PEEK threaded rods are available in lengths greater than 1 foot. The minimum order quantity is a total of 6 of rod which can be cut as one- 6ft rod, two-3ft rods, etc. o ASME B1.1
o DIN 975

PEEK Washers 

Washer      Flat Washers Many sizes of PEEK washers are in stock and ready to ship. PEEK washers are available per SAE, USS, and oversized, as well as custom sizes upon request. o ASME 18.21.1
o SAE / USS
o DIN 125 / ISO 7089 /
  ISO 7090
o DIN 126 / ISO 7091

Not sure what material is best for your application?

Contact an Expert

Use Our Material Selector

Questions?

Our material experts are ready to help guide you through your specific application.

Contact an Expert