A286 / Alloy 660 for excellent high temperature oxidation resistance

• Good material for high temperature oxidation resistance
• Maintains high strength at elevated temperatures
• Specifications & heat treatments
• A286 chemistry
• ASTM A453 Grade 660
• A286 Datasheet

A286 screws, also known as Alloy 660 screws are stainless steel alloy which contains iron, nickel and chromium. A286 set screws are known for their high strength, creep resistance and oxidation resistance at elevated temperatures once age hardened.  As a result, A286 screws provide high levels of strength from room temperature up to about 1300°F (700°C).

A286 set screws are also mildly corrosion resistant. While they should not be used for strong acid environments, they provide excellent oxidation resistance up to 1500°F (815°C) in conditions that would typically be found in high temperature exhaust streams.

Applications

Because of the properties of Alloy 660 / A286, these set screws are often found in high temperature engine, manifold, exhaust and turbine applications as well as off-shore oil & gas applications. In addition, A286 / Alloy 660 is also non-magnetic and finds a niche in non-magnetic cryogenic equipment. We also offer screws per ASTM A453 Grade 660. This specification ensures tensile strength and rupture properties for the most critical applications.

Resources: A286 Torque Specs

Screw Types: 12 Point Screws, Button Head Cap Screws, Flat Head Screws, Hex Cap Screws, Pan Head Screws, Set Screws, Socket Head Cap Screws, Tamper Resistant Security Screws, Torx Screws, Vented Screws

A286 / Alloy 660 Set Screw Features & Benefits

A286 set screws are unique in that they have no screw head, meaning that they have no protruding part past the threaded shaft. They are thread only and are available with a socket or slotted driver insert at one end. Set screws are used to secure an object within or against another object. Typically they secure a rotating part such as a gear or shaft. A286 / Alloy 660 set screws are driven through a threaded hole in the rotating part until it is tight against the inner object, preventing from moving relative to the outer object. Set screws are available with various points depending on the application.

Cup Point 
This is the most commonly used set screw and is identified by a cup-shaped indentation on one end. A286 cup points are typically used for a quick, semi-permanent or permanent applications where it is acceptable to cut the cup point edge of the screw.

Cone Point
A cone point is easily identifiable by its sharp cone-shaped point – just like an ice cream cone. A286 / Alloy 660 cone point set screws deliver the strongest clamping force due to the deep penetration of the point. As a result they are used for permanent assembly.

Flat Point
The cheapest and simplest of the set screw point styles, this screw has a flat surface on the bottom of the screw. This type is used when you need the ability to frequently change parts and require minimal shaft deformation.

ASTM A453 Grade 660

Material specification ASTM A453 Grade 660 applies to bolts, studs, studs and other fasteners. It ensures fasteners meet strength standards for use in high temperature bolting applications. ASTM A453 Grade 660 is classified into 4 property classes / heat treatments: A, B, C & D, each designated with different tensile and stress rupture properties. The most common of the ASTM 453 classes are class A or D. The grades A, B and C all have the same minimum tensile strength and minimum yield strength of 130ksi and 85ksi respectively. However grade D has a significantly better yield with a min tensile of 130ksi and a min yield of 105ksi.

Additional A286 / Alloy 660 Specifications, Cold Working & Heat Treatments

AMS A286 / Alloy 660 Heat Treatments

By AMS numbers, the most common for A286 / Alloy 660 is AMS 5737 (same as Grade A) and then AMS 5732 (same as Grade B).

A286 / Alloy 660 Cold Worked Fasteners

For additional strength, A286 could be aged and cold worked to achieve a min ultimate tensile strength of 160ksi upon request.

Additional Specifications

UNS S66286, ASTM A453, AMS 5525, AMS 5726, AMS 5732, AMS 5737, AMS 5804, EN 1.4980, GE B50T1181, GE B50T12, GE B50T81, Werkstoff 1.4980, ASTM F2281

A286 / Alloy 660 Chemistry

Mechanical Properties